What is the specification of bathroom tile laying process? How to control a series of problems in the bathroom tile laying process? Today, Xiao Bian introduced the specifications of the bathroom tile paving technology from the aspects of the bathroom tile paving, paving, and post- paving . Paving tiles in accordance with the rules of the process can reduce the problem of bathroom tile paving. Let's take a look.
First, the bathroom tile before the process specification
1, bathroom tile specifications and area coordination
Bathroom tile specifications should not be too large, the overall size is too large to feel uncoordinated, and at the same time not easy to install floor drain. General kitchen tiles are mostly 300*300 or 330*330.
2, before the bathroom tile paving plan to do brick
Paving bricks before making a plan, try not to appear less than one-third of the narrow columns. It must be processed and cut, and it is advisable that after the tile is cut, it should be greater than two-thirds.
3, confirm the tiles used before paving
Before the bathroom tile is tiled, confirm the tiles used in the bathroom wall everywhere to prevent confusion of the bathroom tiles, so as to avoid the phenomenon of misuse of tiles.
4, do waterproofing before bathroom tile laying
The tiled front wall of the bathroom needs to be treated with waterproofing. If you use the method of sticking the tiles first and then put them on the tile, you need to make a water-retaining test before paving the tiles. It is best to make the floor waterproof again.
5, understand the direction of hydropower wiring
Before laying, it is necessary to remember the line direction of the wall ground water pipe wires. It is better to keep the circuit and water route maps, so that it can be easily searched for in the future.
Second, the bathroom tiles in the process specification
1, the ratio of cement mortar paving bathroom tiles
The cement used for cementing the bathroom tiles is No. 425 cement. The mixing ratio of cement sand shall not be greater than 1:3. If the cement content is too heavy, the expansion coefficient of the cement will cause the cracking of the tiles and reduce the service life of the tiles.
2, bathroom tiles soaked in water
If glazed wall tiles are used in the bathroom and cement mortar is used as the adhesive, the tiles need to be soaked with water, and the time for soaking the water is appropriate after the tiles are completely soaked. The time is usually 30 minutes. .
3, paving to stay in the seam
Paving bathroom tiles, whether belonging to a seamless brick, must be left seam, it is recommended not less than 1mm, ordinary wall tiles to 1.5-2mm is appropriate, antique brick gap can be appropriately widened.
4, bathroom wall tile height
The paving height of the bathroom wall tiles is higher than the height of the ceiling, generally not less than 10 cm.
5, tile texture alignment
Pay attention to the texture of the tile when paving the tile, do it along the texture paving, the front and back of the tile line should pay attention to its direction, do not paste down, the texture of the tile waist line and the brick texture consistent.
Third, the bathroom tile after the process specification
1, bathroom tile joint interval length
Stitching should be done after the tiles are dried. It is usually carried out after 24 hours.
2, walking to dry after the ground
After the floor tiles are tiled, they must wait for the floor to dry before walking around the tiles or other kitchen and bathroom renovation projects.
3, after the bathroom tile inspection
After the tiles are laid, it is necessary to check them. If it is found that there is an empty drum, it is better to patch and refill the defective areas.
4, bathroom tile wall punching strength
The wall punching needs attention, and it is best to spray water at the hole where the hole is punched for cooling treatment to prevent the tile from bursting due to the local temperature change of the tiles in a short time.
5, empty wall inspection
When drilling a hole in the wall, be sure to check if there is any empty drum. Also, check the pipeline diagram of the hydropower reform that has been saved and do not hit the pipeline.
The above specification about the bathroom tile laying process is briefly introduced here, and I hope to help you. For more information, please visit this website. Stay tuned.
Bathroom tile paving
Ultra Plantâ„¢ Grow Light offers One Chip Technology aimed to meet your indoor growing expectation such as improve plants' quality, increase yield, or better the margin, etc., all for helping you realize a higher return on your crops.
Ultra Plantâ„¢ Grow Light is combined our advanced All-In-One technology with patented optical design and customized light full spectrum supported from our experienced LED engineers, plant specialists and other partners working on horticulture.
From Ultra Plantâ„¢ APP, you are able to schedule the growing process including photoperiod, brightness and spectral in advance. The lighting system will help you grow smarter, easier and better.
Ultra Plantâ„¢ is the most versatile horticultural grow lighting fixture for indoor plants with flexible full spectrum, brightness control and uniform, wider light distribution, suitable for top lighting of all types of crops. No matter it applies to anywhere for any crop, Ultra Plantâ„¢ can do perfect work for you.
Grow Light On Weed,Full Spectrum Indoor Led Grow Lights,Full Spectrum Greenhouse Led Grow Light,Grow Light On Weed For Sale
Feton Corporation , https://www.ultraplantgrowlights.com